MOT advisory: brake pads wearing thin, what to do

· 4 min read

A "brake pads wearing thin" advisory means the tester could see your pads are getting low, but they're not yet worn to the point that fails an MOT. The car passed. Pads wear every time you brake, though, so this advisory usually becomes a fail if you leave it, and it's a cheap, quick job to sort before it does.

What the tester saw

On your certificate it usually reads "Nearside Front Brake pad(s) wearing thin (1.1.13 (a) (ii))", with the side and axle telling you which wheel. Section 1.1.13 of DVSA's MOT inspection manual covers brake linings and pads, and the reference in brackets points to the pad wear items in that section.

The MOT must be done without dismantling, so the tester doesn't take wheels off. They look at the pads through the wheel, or from underneath, and judge how much friction material is left. That's why the advisory doesn't come with a measurement, and why the garage may find the pads are a little better or worse than the tester could see.

If the wording on your sheet is new to you, our guide to what advisory means on an MOT covers the basics.

Will it fail next MOT?

Likely, if left. The manual sets two fail points for pads:

Wording Reference Category
Brake lining or pad worn down to wear indicator 1.1.13 (a) (i) Major (fail)
Brake lining or pad worn below 1.5mm 1.1.13 (a) (ii) Dangerous (fail)

The manual explains that some pads have a metal wear indicator that touches the disc and squeals when the pad is worn out, while others have a cut in the pad that, once worn away, shows the pad needs replacing. Reach either point and the car fails.

How fast you get there depends on your driving. Town driving with lots of stops wears pads much faster than motorway miles. One owner on a Toyota forum reported getting this advisory and then a dangerous fail for a pad under 1.5mm soon after, so don't assume you've got a full year. For the bigger picture, see is an MOT advisory a fail.

Is it safe to drive?

Yes, for now. The pads still work and your braking was good enough to pass the test. The risks come later:

  • Less margin. The closer the pads get to the wear limit, the sooner a normal week of driving tips them into a fail, and you won't always notice it from the driver's seat.
  • Disc damage. Once the friction material is gone, the metal backing plate grinds into the disc. Then a pads job becomes a pads and discs job. Our guide to the brake disc worn, pitted or scored advisory covers that.

Get it checked straight away if you hear squealing or grinding, feel a vibration through the pedal, or the car pulls to one side when you brake.

How to check your pads yourself

  • Look through the wheel. On many alloy wheels you can see the calliper and the edge of the pad against the disc. If the friction material looks thinner than the metal backing plate behind it, it's low.
  • Listen. A high-pitched squeal when braking can be the metal wear indicator touching the disc.
  • Watch the dashboard. Some cars have a pad wear warning light. The manual says an illuminated wear indicator isn't a fail by itself, but it does mean the pads are near the end.

If you can't see the pads, a garage can measure them in a few minutes with the wheel off.

What it costs to fix

The fix is new pads on that axle. Pads are always replaced in axle sets, both front wheels or both rear, so braking stays even.

Job Guide price, parts and labour
Front pads, one axle £105-£140
Rear pads, one axle £100-£130
Front pads and discs, one axle £190-£240

Sources: Bumper's 2026 brake pad guide (front £120-£140, rear £110-£130) and webuyanycar's price table (front £105-£135, rear £100-£130, front pads and discs £190-£240). These are guide prices for independent garages and vary by car, so prestige and performance models cost more. Ask for a quote for your registration.

What to ask the garage

  1. "How thick are the pads now?" A real number in millimetres tells you how urgent it is.
  2. "Are the discs OK, or do they need doing too?" If they're close to the limit, doing both at once saves a second labour charge.
  3. "Front or rear, or both?" Front pads usually wear faster because they do more of the braking.
  4. "Can you check the brake fluid while it's in?" Not part of the advisory, but it's often done at the same time.
  5. "Anything else on the brakes?" A corroded brake pipe or a service brake fluctuating advisory is worth looking at on the same visit.

Common questions

Can I drive with brake pads wearing thin?

Yes, the car passed and the pads still have friction material left. Get them replaced soon, and straight away if you hear squealing or grinding or the brake warning light comes on.

How many miles do I have left on thin pads?

Nobody can give an honest number without measuring the pads. It depends on how thick they are now and how you drive. Ask the garage for the measured thickness.

Do I need new discs as well as pads?

Not always. If the discs are within the maker's limits and not badly scored, new pads alone are fine. If you also had a brake disc advisory, it's usually cheaper to do both at once.

Does a brake pad warning light fail the MOT?

No. The MOT manual says an illuminated brake wear indicator is not a reason for failure on its own. It does mean the pads are low, so get them looked at.

Sources

  1. MOT inspection manual: brakes, 1.1.13 Brake linings and pads (DVSA)
  2. MOT inspection manual: introduction (DVSA)
  3. How much does it cost to replace brake pads? (Bumper, updated 20 July 2026)
  4. How much does it cost to replace your brake pads? (webuyanycar)
  5. When should I get my brakes checked? (AA)
  6. MOT fail after a pads wearing thin advisory, owner report (Toyota Owners Club forum)

Read next